Capricorn RC have released two new progressive spring sets for use with most modern 1/8th scale on road shock absorbers. Available in hard black and medium silver versions, the springs are softer at the beginning, perfect for absorbing bumps, and get harder the more they are compressed, ensuring good stability and handling in the corners. Sold in sets of 4 complete springs.

Source: Capricorn RC [capricornrc.com]

Read the original here:
Capricorn RC Progressive spring sets

Numbers of TRAXXAS R/C model parts for monster truck has just arrived rcMart.com! Please check the list below for your desired Traxxas parts:

Model No.
Description

1942
Traxxas Rod Ends (16 long & 4 short) / Hollow Balls Connectors (18)

2660
Traxxas Big-Bore Shocks

2662
Traxxas Aluminum Big Bore Shocks

3737
Traxxas Turnbuckle & Camber Link

3953
Traxxas Spur Gear 1.0P 36T For Revo / Slayer

3998
Traxxas [...]

Read the original:
Traxxas parts is coming back to rcMart !!!

Numbers of TRAXXAS R/C model parts for monster truck has just arrived rcMart.com! Please check the list below for your desired Traxxas parts:

Model No.
Description

1942
Traxxas Rod Ends (16 long & 4 short) / Hollow Balls Connectors (18)

2660
Traxxas Big-Bore Shocks

2662
Traxxas Aluminum Big Bore Shocks

3737
Traxxas Turnbuckle & Camber Link

3953
Traxxas Spur Gear 1.0P 36T For Revo / Slayer

3998
Traxxas [...]

See original here:
Traxxas parts for monster truck arrived rcMart.com!

The Factory Team 12R5.1 is the latest evolutionary step in Associated’s twenty-five years of 1:12 scale racing history. New for the RC12R5.1 is the wide three-point rear pod that has been optimized for fitting brushless motors as well as heat dissipation. The 12R5.1 is built on a 2.5mm woven carbon fiber chassis that utilizes a pivot-ball link rear suspension that allows for independent adjustments for chassis roll, bump, and alignment.

Having the ability to make these chassis adjustments independently gives the 12R5.1 greater potential for the best possible handling on any track surface. While testing, the pivot-ball link chassis has proven to be more durable in high-speed impacts and excels in bumpy track conditions.

The 12R5.1 features shocks with a through-shaft design providing equalized damping throughout the full stroke of the shock in both directions without any unwanted rebound. The center shock tower has four mounting positions that split the spring rates for even finer adjustments. The center shock also controls the chassis droop and can be adjusted on the car with a turnbuckle wrench, making it easier and quicker to get dialed in.

The 12R5.1’s “Active Strut” front end has been optimized, featuring symmetric components with adjustable caster and track width, as well as a front axle with wheel nut. Factory Team blue aluminum servo mounts position the servo flat on the chassis for a lower center of gravity and include Ackermann adjustment spacers. The foam front bumper helps protect body and chassis during impacts.

The 12R5.1 comes ready for brushless with a new optimized wide rear pod. The rear pod features a woven carbon fiber top plate and Factory Team blue aluminum machined motor mount, left side bulkhead and motor mount standoff. The woven carbon fiber top plate attaches to the motor mount and left side bulkhead at three points, and uses an integrated standoff, making the rear pod more rigid. Front-to-rear chassis balance is optimized at the center of the battery, allowing an easy transition to 3.7V LiPo batteries.

12R5.1 Factory Team features:
- Wide rear pod allows easy installation of brushless motors and features Factory Team blue aluminum machined motor mount, left side bulkhead, and standoff.
- Accepts single-cell LiPo battery packs without changing the front-to-rear weight bias.
- Factory Team shocks feature a through-shaft design, making for equal damping with no rebound in both directions.
- Active strut front end features symmetric components with adjustable caster and track width, as well as a new front axle with wheel nut.
- Woven carbon fiber center shock tower allows for incremental adjustments of rear spring rate.
- Factory Team pivot ball-link chassis allows for independent adjustment for roll, bump, and alignment.

Source: Associated [rc10.com]

Source:
Associated Factory Team 12R5.1

Ultimate Racing have announced the release of new big bore shock spring kits. Each kit (front and rear) comes with 6 shock springs that fits the majority of 1/8th shocks absorbers on the market. The kits contain 3 pairs of springs of 3 different hardness to adapt the shock performance to the different track conditions. Made of high resistance elastic steel that ensures the spring hardness and long live, each spring pair is differentiated with different shades of grey.

Source: Ultimate Racing [ultimateracing.es]

Read the original post:
Ultimate Racing Big bore spring sets

 
ANDERSON Spares & Optional Parts Re-Stock!!!Please check the list below for your desired ANDERSON parts:

Item No.:                                               Description:
MH-258165              13T Pinion Gear For Anderson MB4/MB4 Truggy
258300                    Diff. Set For Anderson MB4/MB4 Truggy
258301                    Diff. Bevel/Case Set For Anderson MB4/MB4 Truggy
258304                    Main Gear (45T) For Anderson MB4/MB4 Truggy
258305                    Drive Gear Set For Anderson MB4/MB4 Truggy
258307                    Main Chassis For Anderson MB4/MB4 Truggy
258308                    Moter Setting Plate For Anderson [...]

Read the original:
ANDERSON Spares & Optional Parts Re-Stock!!!

Search Engine Keywords:

• anderson mb4 parts